Use Real NACE Achieve the NACE-CIP2-001 Dumps - 100% Exam Passing Guarantee
Verified NACE-CIP2-001 Q&As - Pass Guarantee NACE-CIP2-001 Exam Dumps
NEW QUESTION # 36
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - Cross Hatch
- B. Method A - X Cut
- C. Method B - X cut
- D. Method A - Cross Hatch
Answer: B
NEW QUESTION # 37
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Lower the blast pressure
- B. Move the nozzle quicker
- C. a), b) and c)
- D. Increase the standoff distance
Answer: C
NEW QUESTION # 38
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Advise the coating applicator supervisor of your readings
- C. Check to See if the dehumidification equipment is operating correctly
- D. Document the readings at the end of the shift
Answer: B
NEW QUESTION # 39
NACE International Standards are developed by:
- A. Government mandates
- B. Regional mandates
- C. International mandates
- D. Standard committees
Answer: D
NEW QUESTION # 40
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. urethanes.
- B. powder coatings.
- C. inorganic zincs.
- D. epoxies.
Answer: C
NEW QUESTION # 41
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. disposed of properly.
- C. mixed with uncontaminated abrasive
- D. washed with clean potable water prior to Use.
Answer: B
NEW QUESTION # 42
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION # 43
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Use a generally accepted industry standard and to take readings
- C. Develop your own methodology and proceed take the readings
- D. Refuse to take readings until an is in place
Answer: B
NEW QUESTION # 44
The HATE adhesion tester uses
- A. compressed air to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. a special tape to apply pressure to the test dolly.
- D. mechanical means only to apply pressure to the test dolly.
Answer: B
NEW QUESTION # 45
The most likely area of failure on a buried external pipeline coating is the:
- A. Areas exposed to Ultra Violet light
- B. Field joint coating
- C. Ground bed
- D. Mainline coating
Answer: B
NEW QUESTION # 46
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It will result in a very slippery surface
- B. It doesn't contain biocide
- C. The floating structure is stationary
- D. It contains biocide
Answer: D
NEW QUESTION # 47
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of chemical exposure
- B. Risk of skin
- C. a), b), and c)
- D. Risk of acid or caustic splashes
Answer: C
NEW QUESTION # 48
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Surface profile prior to coating
- C. Contamination levels prior to coating
- D. Compressive and tensile strength prior to coating
Answer: B
NEW QUESTION # 49
The Inspectors' goal at the Pre-Job Conference is to:
- A. Manage the meeting so it doesn't go off topic
- B. Discuss contractual requirements
- C. Take accurate meeting minutes for distribution
- D. Obtain a clear understanding of the Specification
Answer: D
NEW QUESTION # 50
Coating surveys may include which steps?
Select All That Apply:
- A. Evaluate the coatings performance
- B. Summarize the collected data
- C. Develop a survey plan
- D. Schedule the remedial work
Answer: A,B,C,D
NEW QUESTION # 51
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Standard buffer solution
- C. Standard solvent solution
- D. Distilled water
Answer: B
NEW QUESTION # 52
When conducting inspections the Inspector should follow which standards:
- A. The specified standards
- B. Australian standards in Australia
- C. ISO standards in Europe and Asia
- D. NACE and SSPC standards in North America
Answer: A
NEW QUESTION # 53
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Use creative writing to cover over the fact they are missing
- C. Re-create the reports as not much was going on during night shift anyway
- D. Plainly state in your report that they are missing
Answer: D
NEW QUESTION # 54
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. All types of inspection without supervision
- C. Visual inspection only
- D. Visual inspection and Non-destructive testing
Answer: A
NEW QUESTION # 55
......
Check the Free demo of our NACE-CIP2-001 Exam Dumps with 100 Questions: https://certification-questions.pdfvce.com/NACE/NACE-CIP2-001-exam-pdf-dumps.html